Features and Specifications |
Jain Micro Duct
-
Jain Micro Ducts are specifically made for installation in the existing (new or old, empty or preoccupied) HDPE / PVC ducts by blowing, jetting or pulling technique. The ducts can be bunched & blown in various combinations & colors thus allowing extra channels for future cabling needs & increased pathway. Its low sliding friction aids in easier blowing & jetting of micro ducts & allows longer pulling distance thus increasing duct integrity resulting in quality installation at lower cost.
-
Jain Micro Ducts are available in 7mm, 10mm & 14 mm OD with different wall-thicknesses.
-
Micro ducts are available with permanently lubricated smooth inner wall or permanently lubricated ribbed inner wall.
Jain Anti-Rodent Duct
-
Ducts are generally installed by direct burial method. At many places rodents are present even at depth of more than one meter below ground level. Unlike human beings the front teeth of rodents grow throughout their life., hence to trim it they chew soft materials like PE & PVC pipes to keep their their teeth within size. This results in damages to the pipes & the cable in it. Jain anti rodents ducts provides the best solution to such problems by incorporating a bitterent in the pipe to dissuade rodents from chewing it. Antirodent ducts are tested at institute for Toxicological Studies, Pune for its antirodent properties. Antirodent ducts are available in various sizes starting from 32 mm onwards.
|
Jain Fire Retardant Duct
|
Technical Specifications for Micro Duct: |
| S.No. |
Parameter |
Specification / Tolerance |
| 1 |
Density |
0.940 to 0.958 g/cc at 27ºC |
| 2 |
Melt Flow Rate |
0.2 to 1.10 gm /10 Minute at 190ºC & 5 kg load |
| 3 |
Minimum Bend Radius |
No cracking, splitting, breaking or permanent reduction in diameter when bend to 180º at radius of 10 times the diameter |
| 4 |
Internal Pressure Test |
5 Minutes at 27ºC & Induced stress at 3.8 mpa. |
| 5. |
Internal Coefficient of friction |
Max 0.1 at 6.8 Kg load |
|
Dimensions (in mm) of Silicoat PE Micro Duct : |
| Nominal Size |
Outer Diamter |
Wall Thickness |
Inner Layer Wall Thickness |
Ovality |
| OD |
ID |
MIN |
MAX |
MIN |
MAX |
MIN |
| 7.0 |
5.5 |
6.9 |
7.1 |
0.65 |
0.75 |
0.10 |
0.20 |
| 10.0 |
5.5 |
9.9 |
10.1 |
2.15 |
2.25 |
0.10 |
0.20 |
| 10.0 |
8.0 |
9.9 |
10.1 |
0.9 |
1.0 |
0.10 |
0.20 |
| 10.0 |
7.6 |
9.9 |
10.1 |
1.1 |
1.2 |
0.10 |
0.20 |
| 12.0 |
8.0 |
11.9 |
12.1 |
1.90 |
2.10 |
0.10 |
0.20 |
| 12.0 |
9.6 |
11.9 |
12.1 |
0.90 |
1.0 |
0.10 |
0.20 |
| Note * 14/10 mm size also available |
|
|
|
Go to related product category: Pipes |
Click here for more details |
